Did you know?

Litter-Robot 4 features a bonnet that covers the globe and functions as a guard for the waste port as the globe rotates. Sensors on the unit detect if the bonnet is on or off. This ensures that Litter-Robot will not rotate if the bonnet has been removed.Litter-Robot 4 is equipped with OmniSense™ detection that utilizes laser and weight sensor technology to provide real-time litter and waste drawer levels. ... To remove the bonnet completely, unlatch the center tab on the bonnet from the catch clip on the unit frame behind the robot. Set the bonnet aside. To remove the globe, grab the black ...Litter-Robot 4: Yellow Flashing (Bonnet Removed) Litter robot 3 bonnet sensor bypass : r/litterrobot Litter-Robot 3 Troubleshooting | Learn more on Litter-Robot Blogemptying the robot of litter entirely, cycling, and then adding litter again The litter level reader is still inaccurate. I eventually added some new litter yesterday, bringing it to the “optimal” level in the robot. Now the app finally reads that the robot is halfway-full of litter (an increase from the “low” reading).Remove the bonnet by pressing the latches on both sides of the bonnet, then lift while rotating it backward. There are two plastic tabs on the back of the bonnet that should slide up and out of the base. ... Litter-Robot uses two magnets located in the globe gear track to monitor the position of the globe. The magnets could be missing or put in ...My Litter Robot 4 arrived with the bonnet misaligned. Even though you can reattach the bonnet, the bottom of it doesn't line up with the unit. ... Please DM us with the serial number if you receive any bonnet-removed notifications. From the picture, your bonnet connectors at the top are in place to allow the robot to function. We are here to ...1. Hold the fence upright inside the globe. 2. Tilt the bottom of the fence toward you to align the back of the fence with the built-in kickguard on the globe. 3. Keep the wing tabs of the fence inside the globe while rotating it downward. Gently pull forward and push down on the front of the fence to snap it over the lip of the globe.You may have to update your firmware. Follow these steps: In the Whisker app, select your Litter-Robot 4 unit from the dashboard. Tap on Controls in the bottom right corner.. Scroll to the bottom of the page and tap the Robot Information panel.. On the Robot Information page, select Update Firmware to begin the update process.This will take between 5 and 27 minutes to complete.The Litter Robot III used to have an Internal shield. Its main function is to provide a barrier between the working surface of the Globe and the space used by your cat. The position of the Internal Shield during cycling is controlled by the Key located at the back of the Globe. In March 2018, the Litter-Robot III was slightly modified.Litter-Robot 3. We have a 3 year old Litter Robot 3. A few months ago we started to have an intermittent issue where the robot will pause over and over during cycling. Looking at the activity in the app it shows bonnet removed multiple times during the cycle, but the bonnet is securely in place. FYI, I recently replaced the drawer sensor and ...Keep your automatic litter box in top shape for years to come with Litter-Robot replacement parts and refresher items. Use our DIY repair guides and videos.-this is a cat problem not a litter robot problem Bonnet - didn't connect all the way at the top, causing 'bonnet removed' errors -you didn't connect the bonnet all the way at the top and caused "bonnet removed" errors Which of these were caused by my lack of education? -see answers above.Description. Litter-Robot 3 Open Air Bonnet. Color: Grey. Features replacement for the Litter-Robot 3 Open Air bonnet. The Litter-Robot 3 Open Air Bonnet - Grey offers a replacement bonnet for the Litter-Robot 3 Open Air. What's Included. 1x Litter-Robot 3 Open Air Bonnet - Grey. Multimedia. Based on 1 review.The globe will not rotate without the bonnetInspect the bonnet connections. Remove the bonnet Get started by following the steps below. If possible, place Litter-Robot in the same location as the old litter box (at least during transition). Make sure the unit is on a firm, level surface in a cool, dry location. Locate the unit near a power outlet. Ensure the unit isn’t pushed against a wall or into a corner (must not be touching any ...Cleaning the sensors. With the globe, bonnet, and drawer removed, lean the unit backward so that you can look into the holes on the bezel to see each sensor. Using a clean, dry cotton swab, carefully clean the surface of each sensor to remove any dust. It is important to note that it will be very difficult to see any dust, specifically on the ... Litter-Robot 4 continuously monitors the motor curre Bonnet Connector Wires PREPARATION Press the Power button to turn the unit off, and unplug it from the wall. Remove the Bonnet, Globe, and Waste Drawer. The plastic component that covers the Control Panel on the Base is called the Bezel. Unscrew the 5 screws to remove the Bezel.Empty the globe from the cat litter by pressing the empty button located on the control panel. Empty button of Litter Robot 4. 3. Clean very well all the residues of cat litter that may be trapped inside the globe with the help of a brush. This will prevent residues of clumping litter from getting mixed with water (much harder to remove) while ... Removing the bonnet. To open the bonnet, press and hold the latc

You will need: Phillips-head screwdriver. Press the Power button to turn the unit off. Press the bonnet tabs on either side of the unit to release the bonnet. Rotate the bonnet backward and lift the bonnet up to remove it from the unit. Flip the bonnet over to expose the underside of the bonnet where the circuit board is located.The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. When a cat enters the globe, ... If the cycling light is slowly flashing yellow (about once per second) or you are receiving a Cat sensor interrupt or Bonnet removed notification, this indicates a cycle has been interrupted by a cat entering the ...Community for all things Litter-Robot. Post your experiences, tips, tricks, and hacks. Members Online • ... and immediately resolved the bonnet removed issue. Reply reply Dani-Boyyyy ...Solid Yellow Flashing Yellow Robot cycling Cycle interrupted or bonnet removed Check for excess litter or check bonnet Solid Red... Page 2 Download the Whisker app and follow the Press and hold, while at the home position, to enter control into the socket on the outlet. View and Download whisker Litter-Robot 3 quick start manual online.Size: Beyond big. An average litter box is fairly compact—personally, our old one was 15 inches by 19 inches with 8-inch walls. The Litter-Robot 3, on the other hand, is absolutely huge. This futuristic-looking gadget is almost 2.5 feet—and it measures just over 2 feet wide and a little over 2 feet deep.

Remove the internal shield. Press the Power button to turn the unit off and unplug the unit from the wall. Press the bonnet tabs on either side of the unit to release the bonnet. Rotate the bonnet backward and lift the bonnet up to remove it from the unit. Optional: Empty the waste drawer and clean the globe with water and a mild soap.fatherofraptors. • 3 yr. ago. Flex the bonnet tabs outwards 90 degrees for at least 30 seconds, they are very flexible, so it shouldn't break. https://support-litter …This video shows you how to get the 3 lights on the Litter-Robot 3 to stop blinking. Litter-Robot 3 Buying Options: 💵 Worried about your cats using it? Wan...…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Your need for speed has a hefty price tag. By clicking "TRY IT". Possible cause: Place the bonnet into the hinge behind the robot as shown. Rotate the bo.